정류기 변압기는 정류기 장비의 전원 변압기입니다. 정류기 장비의 특징은 원측이 AC를 입력하고 보조측이 원점을 정류한 후 DC를 출력하는 것입니다. 변환기는 정류기, 역류 및 주파수 변환의 총칭입니다. 정류기는 가장 널리 사용되는 것입니다. 정류기의 전원으로 사용되는 변압기를 정류기 변압기라고 합니다. 대부분의 산업용 정류기 DC 전원 공급 장치는 정류기 변압기 및 정류기 장비를 통해 AC 전력망에서 얻습니다.
정류기 변압기는 정류기 장비의 전원 변압기입니다. 정류기 장비의 특징은 1차측이 AC를 입력하고 2차측이 정류소자를 거쳐 DC를 출력하는 것입니다. 정류기의 전원으로 사용되는 변압기를 정류기 변압기라고 합니다. 대부분의 산업용 정류기 DC 전원 공급 장치는 정류기 변압기 및 정류기 장비를 통해 AC 전력망에서 얻습니다. 정류기 변압기는 정류기 시스템에 특별히 사용되는 변압기입니다.
정류기 변환기 기능:
1. 정류기 시스템에 적절한 전압을 공급하십시오.
2. 정류기 시스템으로 인한 파형 왜곡으로 인한 전력망 오염을 줄이기 위해.
정류 변압기의 특성
AC 전원 공급 장치에서 DC 전원을 얻기 위해 정류기와 함께 정류기 장비를 구성하는 변압기. 정류기 장비는 현대 산업 기업에서 가장 일반적으로 사용되는 DC 전원 공급 장치입니다. 그것은 DC 전송, 전기 견인, 철강 압연, 전기 도금, 전기 분해 및 기타 분야에서 널리 사용됩니다.
정류기 변압기의 1차측은 그리드 측이라고 하는 AC 전원 시스템에 연결됩니다. 2차측은 밸브측이라고 하는 정류기에 연결됩니다. 정류 변압기의 구조적 원리는 일반 변압기와 동일하지만 부하 정류기는 일반 부하와 다르기 때문에 다음과 같은 특성을 갖습니다.
① Each arm of the rectifier turns on in a cycle, and the conduction time only accounts for a part of a cycle. Therefore, the current waveform flowing through the rectifier arm is not a sine wave, but close to an intermittent rectangular wave; The current waveforms in the primary and secondary windings are also non sine waves. The figure shows the current waveform of three-phase bridge Y / Y connection. When rectifying with thyristor, the greater the lag angle, the steeper the current fluctuation and the more harmonic components in the current, which will increase the eddy current loss. Since the conduction time of the secondary winding only accounts for a part of a cycle, the utilization rate of the rectifier transformer is reduced. Compared with ordinary transformer, the rectifier transformer has larger volume and weight under the same conditions.
② The power of the primary and secondary sides of an ordinary transformer is equal (ignoring loss), and the capacity of the transformer is the capacity of the primary winding (or secondary winding). However, for the rectifier transformer, the power of the primary and secondary windings may be equal or unequal (when the current waveforms of the primary and secondary sides are different, such as half wave rectifier), so the capacity of the rectifier transformer is the average of the apparent power of the primary and secondary sides, which is called equivalent capacity, that is, S1 is the apparent power of the primary side and S2 is the apparent power of the secondary side.
③ Compared with ordinary transformer, the ability of rectifier transformer to withstand short-circuit electrodynamic force must strictly meet the requirements. Therefore, how to make the product have short-circuit dynamic stability is an important topic in design and manufacturing.